Posted on

Flowering cannabis producing seeds

I have an indoor growroom and in my recent harvest I found seeds in the buds, but I’m sure there are no male plants in the room. I’ve heard that light leakage can cause plants to become hermaphrodites. Is this true, and if so, do you have any tips for avoiding this?

Cannabis plants are monecious. This means they have the ability to be either male or female. Or in the case of hermaphroditism, they can be both. The reason to make sure there are no males or hermaphrodites in your garden is because male flowers make pollen. When pollen touches the white hairs on a flower, it makes a seed, and seeded weed gives you headaches. Even though there are reasons in nature hermaphroditism could be important, such as continuing the species in case there is no male present, hermaphroditism is generally a bad thing when talking about cannabis plants.

Light poisoning is the most common cause for a normal plant to hermaphrodite.

Light poisoning refers to the flowering night cycle of a plant being unnaturally interrupted with light. The best way to prevent this is to close yourself inside your darkened room during the daylight, and then after allowing a few minutes for your eyes to adjust to the dark, check for any light leaks from covered windows, door jams, etc. Also cover all timer and appliance lights with tape.

Negative stressors can combine with small interruptions of the light cycle to cause hermaphroditism, especially with less-stable, clone-only hybridized strains. When the night cycle is abnormally interrupted, it sends a mixed hormonal signal to the plant. This can cause a full female plant to throw some male flowers. Male flowers are easy to identify, especially when side by side with female flowers. Male flowers look like small bunches of bananas, which will take a week or two to swell before they burst and release their pollen.

Read also:

Finding a hermaphrodite in your growroom can happen at any stage of the flowering cycle and is indicated by the presence of male flowers growing on the same plant as female flowers. As with all species in nature this can occur in varying degrees. A plant can become slightly or majorly hermaphroditic. In cases where singular male flowers are found between the branch and stalk nodes, you should be diligently removing them as they grow. You must re-inspect the plant top to bottom every few days to be sure pollination and seeding doesn’t occur. If you find male flowers (anthers) actually growing from within the female flowers (buds) the situation is a little more dire. You can still remove all the male anatomy as it appears, but it will be harder to find and much more prevalent. This is a horrible discovery that leads to a tough decision: Should you let the plant live and risk the whole crop being ruined by seeds?

In either case, once hermaphroditism has compromised the safety and purity of your sensimilla, the plant should not be propagated further. Remember, once a hermy, always a hermy. The plant pictured here is in the tenth and what should have been the final week of ripening, but a timer failed and one light stayed on continuously for almost two weeks, causing this vegetative regrowth. Because the light was continuous, the plant made no pollen. This method of re-vegging can be used to save a flowering plant you have no copies of, but be careful, as this may cause some strains to hermaphrodite.

Purposefully causing a plant to hermaphrodite is called selfing. Gibberellic acid or colloidal silver is typically sprayed onto the female plant. This technique is used to make feminized seeds and uses the plant’s ability to be both male and female to force a female plant to produce male flowers. The pollen contained in these male flowers can only produce female seeds. Just keep in mind that feminized plants should not be used for breeding, as they were produced without a true male, making them genetically inferior.

Marijuana Cultivation/Producing Seeds

Sooner or later every grower is going to want to produce marijuana seeds. Developing a new stable strain is beyond the scope of this discussion and requires the ability to grow hundreds or even thousands of breeding plants. However, just about any grower can manage to preserve some genetics by growing f2 seeds where they have crossed a male and female of the same strain, or can produce a simple cross which would be referred to as strain1xstrain2 for instance white widow crossed with ak-47 would be referred to as a WW x AK-47. You can produce some excellent seed and excellent marijuana this way.

To Feminise or not to Feminise Edit

There are numerous myths surrounding feminized seeds. Feminizing seeds are a bit more work than simply crossing two plants naturally. However it will save you a lot of time in the end. If you make fem seeds properly then there is no increased chance of hermaphrodites and all seeds will be female. This means no wasted time and effort growing males and it means that all your viable seeds produce useful plants. Since roughly half of normal seeds are male this effectively doubles the number of seeds you have.

Feminized seeds are bred to contain no male chromosomes, which will be able to produce the crop of resinous buds sought by most growers. For gardeners who require a quick and easy cultivation process, feminized seeds are the ideal choice. Some medicinal cannabis users may be deterred from growing their own supply because of the perceived difficulty of growing or of identifying the different genders and removing males early in the blooming period. Feminized seed-strains offer a simple solution to these issues, as there is no need to spend time in the first weeks of flowering checking for male plants.

Other times you will have no choice but to produce feminized seed because it will be a female plants genetics that you want to preserve and you won’t have any males. Perhaps you received these genetics via clone or didn’t keep males.

The new thing on the market for commercial Cannabis cultivation are auto-flowering feminized strains. By crossing of the cannabis ruderalis with Sativa and Indica strains many cultivators have created interesting hybrids which boast benefits from both sides of these families.

The first ‘auto-flowering cannabis seed’ which came on the market a few years ago was the Lowryder #1. This was a hybrid between a Cannabis ruderalis, a William’s Wonder and a Northern Lights #2. This strain was marketed by ‘The Joint Doctor’ and was honestly speaking not very impressive. The genetics of the ruderalis was still highly present which caused for a very low yield and little psychoactive effect. Not very attractive.

Auto-flowering cannabis and the easily distributed seed have opened a whole new market in the world of the online grow-shop, making it easy for home growers with shortage of space to grow rewarding cannabis plants in many different varieties. To grow plants indoors, a growing medium (e.g. soil or growing Potting soil, irrigation (water), fertilizer (nutrients), light and atmosphere need to be supplied to the plant.

Auto-flowers have been rising in popularity fast and there are now auto flower growers communities. These Web properties allow users to get information on how to grow these non photo-sensitive plants and what are the best practices when producing and germinating auto-flower seeds.

Selecting Suitable Parents Edit

There are a number of important characteristics when selecting parents. First are you making fem seeds? If you are then both parents will be female. This makes things easier. If not then the best you can do is select a male with characteristics in common with the females you hope to achieve from the seed.

Obviously potency, yield, and psychoactive effects are critical to the selection process. But some other important traits are size, odor, taste, resistance to mold and contaminants, early finishing and consistency.

Collecting and Storing Pollen Edit

In order to collect pollen you simply put down newspaper around the base of the plant. The pollen will fall from the plant onto the newspaper. You can then put this newspaper into a plastic bag and store it in the refrigerator or freeze it. Pollen will keep for a few months in the refrigerator and can be used on the next crop. Filtering the pollen through a silkscreen, drying, and freezing can extend viability for decades. At least one reader indicates success using pollen treated in this manner and stored at -30 c for 17 years. The chance of viability does decrease with time, even in the freezer, so the more fresh the pollen the better. Wrapping the pollen in a layer of aluminum foil and then a layer of plastic should help to protect it from freezer burn. Additionally, oxygen evacuation such as with a heavy gas like nitrogen or vacuum sealing should provide additional assurance of preservation.

Pollinating a Plant Edit

To pollinate a plant you can brush the pollen on a flower with a cotton swab or you can take the plastic bag, then wrap the flower inside it and shake, trapping the pollen inside for easier transportation. In this way you can selectively pollinate plants and even individual buds and branches.

Male Isolation Edit

A male plant or a plant with male flowers will pollinate your entire crop rendering it seedy. You probably don’t want THAT many seeds so how can you avoid it? Moving the male to another room might work but if that other room shares an air path via ducting or air conditioning then pollen may still find its way. One technique is to construct a male isolation chamber.

A male isolation chamber is simply a transparent container such as a large plastic storage tub turned on its side (available at your local megamart). Get a good sized PC fan that can be powered with pretty much any 12v wall adapter, by splicing together the + (yellow or red on fan, usually dotted on power adapter) and the – wires (black on fan, usually dotted power adapter) just twist with the like wire on the other device and then seal up the connection with electric tape. Then take a filtrate filter and cut out squares that fit the back of the pc fan so that the fan pulls (rather than pushes) air through the filter. Tape several layers of filter to the back of the pc fan so all the air goes through the filter. Now cut a large hole in the top of the plastic container and mount the pc fan over top of it so it pulls air out the box. You can use silicon sealant, latex, whatever you’ve got that gives a good tight seal.

This can be used as is, or you can cut a small intake in the bottom to improve airflow. Pollen won’t be able to escape the intake as long as the fan is moving but you might put filter paper over the intake to protect against fan failures. You can also use grommets to seal holes and run tubing into the chamber in order to water hydroponically from a reservoir outside the chamber. Otherwise you will need to remove the whole chamber to a safe location in order to water the plant or maintain a reservoir kept inside the chamber.

Making Feminized Seed Edit

To make feminized seed you must induce male flowers in a female plant. There is all sorts of information on the Internet about doing this with light stress (light interruptions during flowering) and other forms of stress. The best of the stress techniques is to simply keep the plant in the flowering stage well past ripeness and it will produce a flower (with seed).

Stress techniques will work but whatever genetic weakness caused the plants to produce a male flower under stress will be carried on to the seeds. This means the resulting seeds have a known tendency to produce hermaphrodites. Fortunately, environmental stress is not the only way to produce male flowers in a female plant.

The ideal way to produce feminized seed through hormonal alteration of the plant. By adding or inhibiting plant hormones you can cause the plant to produce male flowers. Because you did not select a plant that produces male flowers under stress there is no genetic predisposition to hermaphroditism in the seed vs plants bred between a male and female parent. There are actually a few ways to do this, the easiest I will list here.

Colloidal Silver (CS) Edit

This is the least expensive and most privacy conscious way to produce fem seed. CS has gotten a bad name because there is so much bad information spread around about its production and concentrations. It doesn’t help that there are those who believe in drinking low concentration colloidal silver for good health and there is information mixed in about how to produce that low concentration food grade product. Follow the information here and you will consistently produce effective CS and know how to apply it to get consistent results.

Simply construct a generator using a 9-12 v power supply (DC output, if it says AC then its no good) that can deliver at least 250ma (most wall wart type power supplies work, batteries are not recommended since their output varies over time). The supply will have a positive and negative lead, attach silver to each lead (contrary to Internet rumors, you aren’t drinking this so cheap 925(92.5%) Stirling silver is more than pure enough. You can expose the leads by clipping off the round plug at the end and splitting the wires, one will be positive and the other negative just like any old battery. Submerge both leads about 2-3 inches apart in a glass of distilled water (roughly 8 oz). Let this run for 8-24 hrs (until the liquid reads 12-15 ppm) and when you return the liquid will be a purple or silver hue and there may be some precipitate on the bottom.

This liquid is called colloidal silver. It is nothing more or less than fine particles of silver suspended in water so it is a completely natural solution. It is safe to handle without any special precautions. [ citation needed ] The silver inhibits female flowering hormones in cannabis and so the result is that male flowering hormone dominates and male flowers are produced.

To use the silver, spray on a plant or branch three days prior to switching the lights to 12/12 and continue spraying every three days until you see the first male flowers. Repeated applications after the first flowers appear may result in more male flowers and therefore more pollen. As the plant matures it will produce pollen that can be collected and used to pollinate any female flower (including flowers on the same plant).

Silver Thiosulfate (STS) Edit

Silver Thiosulfate is a substance that has similar principle, application and results of CS, but is more difficult to make. STS is more difficult to acquire, but it can still be obtained directly from a chemical supply company. STS is not an expensive or controlled substance.

Gibberellic Acid (GA3) Edit

This is probably the most popular way to produce feminized seed, but at the same time the least effective. GA3 is a plant hormone that also causes the plant to stretch uncontrollably. It can be purchased readily in powdered form, a quick search reveals numerous sources on e-bay for as little as $15. Simply add to water to reach 100ppm concentration and spray the plant daily for 10 days during flowering and male flowers will be produced.

What causes seeds in buds while growing cannabis?

What does it mean to find seeds in your marijuana buds? Is it something to be worried about? This is something that happens while buds are forming in the flowering stage, but can be prevented with the right steps. Learn more below.

There’s a seed in my bud!

Sometimes you don’t see the seeds until they fall out of your buds

What causes seeds?

Seedy buds are the result of pollination. What does that mean? Cannabis buds are flowers. Like other flowers, they make seeds when pollinated. Cannabis buds get pollinated when they come into contact with cannabis pollen while the buds are forming.

Seeds happen when pollen gets on the hairs (pistils) of buds as they’re forming. In other words, seeds in weed are caused by pollination.

This bud is full of fat seeds because pollen got on the pistils during bud development.

Pollen typically comes from the pollen sacs of a male cannabis plant. Male plants spray pollen everywhere when their flowers are mature. Sometimes female cannabis plants will produce pollen (known as herming) due to genetics or stress. Any source of pollen, whether the plant is male or female, can pollinate buds in the vicinity and cause seedy buds.

If you’re not growing with feminized (all-female) seeds, about half the plants will be male and grow pollen sacs (male flowers) that release pollen. Unless you want seeds, male plants should be removed from the grow room immediately because they will otherwise seed all your buds.

Seeds are caused by the presence of male flowers while buds are growing. Male flowers release pollen that pollinates buds and causes seeds to grow.

Any time you see “bananas” or “balls” it’s important to separate that plant immediately to prevent possible pollination. These are the result of a hermaphrodite plant (“herm”) and these structures also release pollen.

Example of a hermaphrodite plant making seeds

You may notice a bunch of little yellow growths in these buds. They almost look like mini bananas. This plant is “herming” or growing male flowers that spew pollen everywhere. If this plant isn’t removed from the grow space, it will pollinate itself and all other plants in the area, causing seedy buds

This is the same plant. You can see that some of the pure white hairs have turned brown early. This is because those hairs were pollinated. If this plant were allowed to continue flowering, there would be a seed growing at the base of all those brown hairs.

You may not realize that seeds are forming while your buds are growing

But once they get really seedy, buds may look like they have huge plump calyxes/bracts (female flowers) or they may even be misidentified as pollen sacs (hermie/male flowers).

When handling the buds after harvest, you may see seeds or hear them as they fall onto the surface below

Does it mean the weed is bad? No!

If it’s very seedy the buds may not feel as potent, though a few seeds here and there won’t make much difference in bud potency. The main problem with seedy weed is that you are getting less smokeable bud for the amount of total mass there. If it is seedless, you will get more bang for your buck. Seedless bud (sinsemilla) is considered to be the highest quality and most potent type of weed.

Seedy weed is still good to smoke

However, cannabis plants waste energy developing seeds that could have been used to fatten buds. When a bud has lots of seeds, it often isn’t as big and plump as it would have if the plant had not been pollinated. Notice how all the mass of this bud is in the seeds. The rest of the bud is airy and small.

Are seeds good to grow?

I’ve seen some growers get impressive results with bagseed (seeds you find in a “bag” of weed), but overall results seem to be hit or miss. Plants can grow in odd ways and often either the yields or quality isn’t as expected. The problem is that seeds often don’t “breed true” to the buds that they came from.

“Found” seeds can sometimes produce excellent results

But sometimes the plants grow poorly or buds don’t turn out anything like the buds you found the seeds in

That is why many growers either stick to clones (which are exactly the same as the “mother” plant) or purchase seeds of a stabilized strain from a trustworthy breeder. Starting with stable genetics helps ensure each of the plants will grow the way you expect, and buds have the smell, yield, and potency you want.

If you’re not sure what strains to get, here are a few recommendations. These strains produce excellent weed and are generally easy to grow. These seeds are all feminized, which means they will only grow female plants (no pollen to worry about!) Click the links for more information.

    – top-shelf looks and smell with classic effects reminiscent of 90s buds but stronger. Easy to grow. – this version is MUCH more potent than regular White Widow. The buds tested between 24-26% THC. Don’t plan to do anything else that day ? – for those who are looking for a face melter. These buds test up to 28% THC and produce buds with quintessentially “American” looks and smell. The mental and physical effects may be too intense for most beginners. is a good choice for commercial growers with high THC up to 30%, big yields, and a short flowering time. is a potent Sativa hybrid with great yields and uplifting unique mental effects is an autoflowering strain that produces photoperiod-quality buds in about 70 days from seed to harvest.

Platinum Cookies is essentially a more potent version of the popular Girl Scout Cookies strain.

How can I tell if it’s a viable seed?

Good seeds are often dark and relatively hard. Very pale or white seeds that can be easily crushed between the fingers often don’t sprout. However, I have been surprised to find some very flimsy seeds sprout and produce amazing plants (we aren’t breeding them for hard seeds after all) so when in doubt, I highly recommend doing the true test to see if the seed is viable – try to germinate the seed and see if it sprouts.

The best way to tell if a seed is viable is to try to germinate it and see what happens.